Jump to content


Urgent - Need Feeder for Harken Mk I Furling Unit


  • Please log in to reply
5 replies to this topic

#1 Drifter

Drifter

    Member

  • Members
  • PipPipPipPipPip
  • 37 posts
  • Location:The Great Lakes

Posted 17 February 2017 - 03:57 AM

I need to locate the 2 piece feeder that bolts to foil on a Harken MK I furing unit. Was in the process of removing and dropped half into the harbor. If there is anyone in the greater tampa bay area with one I will meet you tomorrow to get it. Otherwise, I'm willing to pay any air freight charges to get it here asap.

#2 Moonduster

Moonduster

    Anarchist

  • Members
  • PipPipPipPipPipPipPip
  • 3,345 posts

Posted 17 February 2017 - 10:19 AM

Call your local diver?



#3 Drifter

Drifter

    Member

  • Members
  • PipPipPipPipPip
  • 37 posts
  • Location:The Great Lakes

Posted 17 February 2017 - 11:41 AM

Call your local diver?


Diver will be here this morning, but the harbor bottom is about 2 feet of silt and mud, so there isn't much hope we'll locate it.

#4 bammiller

bammiller

    Anarchist

  • Members
  • PipPipPipPipPipPipPip
  • 1,070 posts

Posted 18 February 2017 - 01:42 PM

You said a MK1 - which is a post 1987 furler - it is make from stainless steel. Feeders are still available. I actually have one on the shelf and I show that Harken has over 100 pieces - part number 812. 

 

However, I think you are referring to the Roll Pin system. The feeder was made from black cast aluminum -  they stopped making those in 1987. Good luck on finding a replacement - You might find a whole furler laying around at a boatyard but not very likely. I get calls for roll pin parts a couple of times a year and supply has really dried up. 

 

If you only hoist the sail once a season, you can actually do without it. You will, however, have to trim your luff tape so it stops above where the feeder used to be located and be VERY careful when hoisting the sail. No wind and an extra set of hands to feed the luff tape in to the bottom edge of the foil will get the job done. 

 

Bam Miller 

.

Attached File  HAR.MKI.Unit1.Rollpin.Parts.PDF   81.27KB   23 downloads



#5 dacapo

dacapo

    Anarchist

  • Members
  • PipPipPipPipPipPipPip
  • 8,595 posts
  • Location:NY
  • Interests:walks on the beach,a good book,a good cry

Posted 23 February 2017 - 07:26 PM

is this it??

 

http://www.ebay.com/...3dYT0cs&vxp=mtr

 

or this?

 

http://www.ebay.com/...4pYT0cd&vxp=mtr

 

or this

 

http://www.ebay.com/...EdYT0Vb&vxp=mtr



#6 CrushDigital

CrushDigital

    Anarchist

  • Members
  • PipPipPipPipPipPipPip
  • 2,807 posts
  • Location:New York, NY

Posted 23 February 2017 - 08:11 PM

This sounds like a problem that could be fixed with 3d printing.






0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users