Recent content by Feisty!

  1. F

    Bolt question- engine mount bracket to flywheel housing

    Clearly, this engine has been painted, so conclusions about what came from the factory based on paint are questionable. An undersized hex probably indicates a non-factory bolt, either different spec or smaller thread. The metric system uses the same thread pitches for several diameters...
  2. F

    Bolt question- engine mount bracket to flywheel housing

    1. Typically, all the bolts performing a particular function will be identical. Pull the others, one at a time, and see what you've got. Metric bolts of different diameters can have the same thread pitch and a size smaller bolt can screw into a larger hole, but will wiggle until tightened. 2...
  3. F

    Trailer Tongue Extension:

    Standard practice in Colorado for keelboats is a trailer mounted launch wheel that is aligned so that the trailer will roll straight and is retractable for towing; and a long enough strap/rope/cable to get the boat in deep enough while keeping the exhaust pipe dry. Lesser variations involve...
  4. F

    Vakaros

    Order #4900 placed 8/9/2021 just delivered ...
  5. F

    Resin infusion with wood veneers

    Vacuum has effects that mechanical compression does not - like causing things like water and polyester resin to vaporize (boil) ...
  6. F

    Resin infusion with wood veneers

    I would expect that wood would outgas slowly under vacuum, possibly producing bubbles. Simple vacuum bagging would preserve the bubbles when cured. Infusion, with a suitable dwell under vacuum and before introduction of resin should reduce the bubbling as well as pressure impregnating the...
  7. F

    Hookah/Snuba Setup

    Given the OP's premise of removing one day's accumulation, and the habit of growth focusing on the shallowest part of the hull where the sun can penetrate, I'd think one could do a 95% job keeping one's head above water and wielding scotchbrite with one hand while hanging on to the gunwale or...
  8. F

    3M 71 - Composite Spray Adhesive

    That's my question. If there's no adhesive the composite has all the strength one expects. If there's a continuous layer of adhesive, it's the strength of the adhesive that rules. Reality is somewhere in between. Unless the resin somehow combines/absorbs/dissolves the adhesive. Which would allow...
  9. F

    3M 71 - Composite Spray Adhesive

    Replacing deck balsa core from underneath. Using 71 to hang flow media on outer skin, then possibly 1/4" balsa to the flow media. Then new inner skin, peel ply, bag and infusion ...
  10. F

    3M 71 - Composite Spray Adhesive

    Replacing deck balsa core from underneath. Using 71 to hang flow media on outer skin, then possibly 1/4" balsa to the flow media.
  11. F

    3M 71 - Composite Spray Adhesive

    Looking for experience with this stuff: composite strength degradation vs application density, actual tack time window vs temperature, bond strength vs application density, gotchas ...
  12. F

    Low Temperature Epoxy Cure

    It's winter in the Rockies and I, thru egregious lack of planning, am doing deck core replacement outdoors in between winter weather episodes.  I can get the interior of the boat (I'm replacing the core from underneath) up to 70F by clever application of timing and electric heat. My question...
  13. F

    Self tacking jib sheeting

    There appears to be a lazy fourth sheet led to the starboard side of this no-longer-self-tacking rig ...
  14. F

    What is it. Fuel filter edition

    RV practice is separate pickups in the tank with the genset pickup higher so you've got enough fuel to motor ...
  15. F

    Stronger aluminium rivets?

    The cantilever puts the far fastener in tension not shear. Pop rivets are really bad at tension. I'd use a SS machine screw and nylon lock nut with your favorite smoodge.
Top